Pro Audio Config

Pro Audio Cases -> Subcategories

Rack Cases -> Subcategories

Soft Racks

Roto Racks

Fly Racks

Shock Racks

MIL-STD Shock Racks

Specialty Racks

Accessories (for Rack Cases)

This case is the perfect solution for mobile conference rooms or events that require equipment to be stored and locked after using.

It features high quality PE foam in two layers to protect the Shure Microflex wireless system. The top layer accommodates 10 MXC420/C or MXC420DF/C microphones. The right side holds 1 MXCWAPT Access Point Transceiver and 1 MXCWNCS Network Charging Station with 10 SB930 Rechargeable batteries inside charger, and features a large pocket (11.625" x 4.75" x 9.75")for cables, power supplies, and other accessories. The bottom layer holds 10 MXCW640 wireless conference units. There is also an additional accessory pocket below the charging station that measures (14.75" x 5" x 5").

This case features three protected hinges with stainless steel pins to provide lid stability, SKB's Trigger Latch® System (which can be retrofitted with TSA recognized and accepted locks), an oversized double grip carrying handle to balance a heavy load, and comfortable oversized snap-down cushion grip handles on each end for a two person carry. The heavy-duty oversized handle and wide set double wheels offer the perfect solution for comfortable transport of the Shure Microflex Wireless System.

Custom cut foam interior for 10 MXC420/C or MXC420DF/C microphones, MXCWAPT Access Point Transceiver, MXCWNCS Network Charging Station with 10 SKB930 batteries installed

Open space below battery charger and additional pocket for accessories

Oversized heavy-duty handles and wide-set double wheels

Ultra high-strength polypropylene copolymer resin

UV, solvent, corrosion and fungus resistant (MIL-STD 810H)

Complete gasket seal makes these cases absolutely watertight (MIL-STD 810H)

Automatic ambient pressure equalization value (MIL-STD 810H)

Patented "trigger release" TSA Locking Latch system

TSA recognized and accepted locks can be retrofitted

Stainless steel locking loops for customer supplied lock

Made In USA

The 3i-1610-MC8 microphone case features high quality PE foam that holds eight handheld, wired microphones stored vertically. The microphone slots are designed to hold the most popular brands of handheld microphones, with finger cutouts that provide easy access. A large 10" x 8" x 9" compartment accommodates cables, direct boxes, and microphone clips. 

SKB iSeries Injection Molded Mil-Standard Waterproof Cases are molded of ultra high-strength polypropylene copolymer resin, featuring a gasket-sealed, water and dust tight, submersible design (MIL-STD 810H) that is resistant to corrosion and impact damage. Standard features include a molded-in hinge, padlock loops, Trigger Latch® System, snap-down rubber over-molded cushion grip handle, automatic ambient pressure equalization valve (MIL-STD 810H), and resistance to UV, solvents, corrosion, fungus and impact damage (MIL-STD 810H).

Custom cut foam interior to hold 8 handheld wired microphones

Snap-down rubber over-molded cushion grip handle

Ambient pressure equalization valve (MIL-STD 810H)

Resistant to UV, solvents, corrosion, fungus, and impact damage (MIL-STD 810H)

This iSeries case was designed to hold the Shure BLXR, GLXDR, SLX, SLX-D, QLX-D, and ULX-D wireless systems. The custom interior foam can accommodate the receiver, quarter and a half wave antenna, handheld mic, bodypack transmitter, lavalier mic, earset head-worn mic, rechargeable battery/AA batteries, mic clip, and power supply.

SKB iSeries Injection Molded Mil-Standard Waterproof Cases are molded of ultra high-strength polypropylene copolymer resin, featuring a gasket-sealed, water and dust tight, submersible design (MIL-STD 810H) that is resistant to corrosion and impact damage. Standard features include a molded-in hinge, Trigger Latch® System, snap-down rubber over-molded cushion grip handle, automatic ambient pressure equalization valve (MIL-STD 810H), and resistance to UV, solvents, corrosion, fungus and impact damage (MIL-STD 810H).

Fits Shure BLXR, GLXDR, SLX, SLX-D, QLX-D, and ULX-D wireless systems

Space for receiver, antennas, handheld mic, bodypack transmitter, and accessories

Automatic ambient pressure equalization valve

Locking loops accept a customer supplied lock

The 3i-1711-SEN case fits the Sennheiser EW-D, EW-DX, EW100, EW300, and EW500 Series Wireless Microphone Systems. The custom cut PE interior foam is designed to securely transport the entire Sennheiser EW Wireless Microphone package including the receiver, antennas, handheld mic transmitter, body pack transmitter, lavalier microphone, mic clip, power supply, spare AA batteries, and other additional accessories. This case will also fit the Sennheiser IEM transmitters and receivers.

Fits EW100, EW300, EW500, and IEM systems

Space for receiver, handheld mic, body pack, and lavalier microphone

Complete gasket seal makes case watertight (MIL-STD 810H)

Automatic ambient pressure equalization valve (MIL-STD 810H)

The 3i-221312WMC Wireless Mic case is part of the Waterproof iSeries of cases with a custom foam interior to protect a variety mic brands including Shure and Sennheiser.

This custom foam interior is designed to hold sixteen handheld wireless microphones vertically. On the side is a removable tray with pick and pluck foam that can be used to hold body pack transmitters or other accessories. Below the tray is space that can be used for cables, direct boxes, and other equipment. This case features a pull out handle and wheels for easy transport. 

Cutouts for 16 handheld wireless microphones

Removable tray with pick and pluck foam for accessories

Complete gasket seal makes these cases absolutely watertight (MIL-STD810G)

Stainless steel locking loops to accept a customer supplied lock

Industrial strength injection molded pull handle with push button release

In-line skate style wheels for easy transport

TSA accepted key locking latches are available

The iSeries 3i0705-3-XSW case is designed to accommodate the Sennheiser XSW-D ENG Set Wireless Audio System. The interior features a custom-cut high quality PE foam that will hold the Sennheiser Mini Jack TX, XLR Female TX, and Mini Jack RX, and also includes an accessory pocket that will house the lav mic and other accessories. 

Custom cut interior for Sennheiser XSW-D ENG Set

Accessory pocket for lav mic and other cables

Rubber over-molded cushion grip handle custom cut foam interior

The iSeries 3i0806-3-AVX case is designed to accommodate the Sennheiser AVX Wireless Audio System. The interior features custom-cut high quality PE foam that will hold the Sennheiser AVX transmitter, receiver, lav mic, and other accessories. There are also two pockets for additional AVX batteries.  

Custom cut interior for Sennheiser AVX system

The 3i-1813-5WMC Wireless Mic case is part of the Waterproof Series of cases with a custom foam interior to protect a variety of brands including Shure and Sennheiser mics to name a few.

The custom foam interior is designed to cradle each mic and will fit up to four handheld wireless microphones, four wireless body pack transmitters and accessories. Convenient finger holes to quickly grab the microphone and easily slide in the body pack transmitters.

Custom foam interior to hold four wireless mics and accessories

The 3i-1813-7WMC Wireless Mic case is part of the Waterproof Series of cases with a custom foam interior to protect a variety of brands including Shure and Sennheiser mics to name a few.

This dual layer custom foam interior is designed to cradle each mic and will fit up to eight handheld wireless microphones, eight wireless body pack transmitters and accessories. Convenient finger holes to quickly grab the microphone and easily slide in the body pack transmitters on their side to protect the antenna. An open pocket is perfect to hold mic clips, batteries and other accessories.

Custom dual layer foam interior to hold eight wireless mics, body packs and accessories

The 3I-2011-MC12 microphone case holds twelve microphones stored vertically and is part of the iSeries waterproof case line. The microphone holes are designed to secure most popular types of handheld microphones, finger cutouts that provide instant access, and a generous storage compartment for cables and microphone clips. The interior is made of high quality PE foam designed to last. The 3I-2011-MC12 microphone case measures 20" x 11" x 8" deep and is covered by SKB's Lifetime warranty. 

UV, solvent, corrosion and fungus resistant (MIL-STD-810F)

Complete gasket seal makes these cases absolutely watertight (MIL-STD-C-4150J)

Automatic ambient pressure equalization value (MIL-STD-648C & IP67)

Custom cut to accommodate 12 microphones vertically

The 3i0907-4-SWK Custom interior Sennheiser EW Wireless System Mic case is a very compact case and is part of the iSeries Waterproof cases. The interior features a custom cut polyethylene (PE) foam interior that will accommodate a wireless plug-on transmitter, wireless body pack transmitter, wireless body pack receiver with an extra spot for a lavaliere microphone plus additional accessories with an overall interior measurement of 9" x 7" x 4", compact yet durable to house your delicate wireless system. 

Custom cut foam to accommodate a Sennheiser EW Wireless System

The 3i-0907-MC3 allows 3 mics to be stored horizontally. Each microphone cutout measures 1.5" wide by 6.75" long with two perforated removable foam pieces, one located on each end allowing microphone sizes up to 8.5" in length. By removing the perforated foam piece near the grill of the microphone you can change the shape from being round to square. This will accommodate other popular hand held microphones with square style grills such as the Sennheiser and Electro Voice mics. The 3I-0907-MC3 case measures 9" x 7" x 4" deep and is the most compact 3-mic case on the market. The case has convoluted foam in the lid for a compression fit and is covered by SKB's Lifetime Warranty. 

The 3i-0907-MC6 holds six mics in a very compact case and is part of the 3i Waterproof Series of cases. It allows 6 mics to be stored horizontally on two separate layers of foam (3 on top and 3 on bottom). Each microphone cutout measures 1.5" wide by 6.75" long with two perforated removable foam pieces, one located on each end allowing microphone sizes up to 8.5" in length. By removing the perforated foam piece near the grill of the microphone you can change the shape from being round to square. This will accommodate other popular hand held microphones with square style grills such as the Sennheiser and Electro Voice mics. The 3i-0907-MC6 case measures 9" x 7" x 6" deep and is the most compact 6-mic case on the market. The case has convoluted foam in the lid for a compression fit and is covered by SKB's Lifetime Warranty.

The 3I-2015-MC24 case is the largest mic case and holds (24) mics vertically. It includes a large accessory section to store cables, mic clips, direct boxes, and more. 